Alvarion Wi^2 AP CLI Especificaciones Pagina 54
- Pagina / 291
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
28 Installation
Chapter 2 - Hardware Installation
2.3.5 Mounting the Wi² Unit
1 With the bottom panel of the unit facing downwards, thread the two 9/16"
wide metal bands supplied through the brackets on the sides of the unit.
2 Rotate the mounting bracket, so that the Wi² faces the Base Station.
3 Secure the Wi² unit to a pole as shown in Figure 2-12.
2.3.5.1 Mounting the Wi² Using the Tilt Accessory
The Wi² can also be installed on a wall or on a non-vertical pole using an optional
tilt accessory kit. The tilt accessory kit (Figure 2-13) includes:
A mounting bracket
3 metal bands for attaching the bracket to a pole
Screws for attaching the bracket to a wall
To pole mount the Wi² unit:
NOTE
The mounting bracket can be rotated up to 45
o
in any direction.
Figure 2-12: Pole Mounting the Wi²
- BreezeMAX Wi² 1
- System Manual 1
- Document History 2
- Legal Rights 3
- Disclaimer 4
- Limitation of Liability 5
- Important Notice 7
- EC Conformance Declaration 10
- Compliances 11
- About This Manual 13
- Table of Contents 15
- and BreezeACCESS VL Wi 16
- System Manual 16
- BreezeMAX Wi 17
- System Manual xvii 17
- System Manual xix 19
- System Manual xxi 21
- System Manual xxiii 23
- Appendix A - Troubleshooting 24
- System Manual xxv 25
- In This Chapter: 27
- 1.1 Introduction 28
- 1.2 Specifications 30
- 1.2.2 Sensitivity 31
- 1.2.3 8 dBi Omni Antenna 31
- 1.2.5 Mechanical 33
- 1.2.6 Electrical 33
- 1.2.7 Connectors and LEDs 33
- LEDs Power 34
- Type Description 34
- 1.2.8 Environmental 35
- 1.2.9 Standards Compliance 35
- 2.1 Hardware Description 38
- 2.1.1 Bottom Panel 39
- 2.1.2 Top Panel 40
- 2.1.3 LED Indicators 40
- Table 2-2: LED Indicators 41
- LED Status Description 41
- 2.2 Installation Requirements 42
- 2.3 Installation 45
- 20 Installation 46
- 22 Installation 48
- BreezeACCESS SU-ODU 50
- Installation 53
- System Manual 27 53
- 2.3.5 Mounting the Wi² Unit 54
- System Manual 29 55
- 30 Installation 56
- 2.3.9.2 Configuring the Wi² 58
- System Manual 33 59
- 3.1 Introduction 62
- Initial Setup through the CLI 63
- 3.3 Logging In 66
- Figure 3-2: Home Page 67
- 4.1 Introduction 70
- 4.3 BreezeACCESS Backhauling 72
- Configuration 72
- 4.4 Advanced Configuration 73
- 4.4.1 System Identification 74
- 4.4.2 TCP / IP Settings 75
- 50 Operation 76
- 4.4.3 RADIUS 78
- Advanced Configuration 79
- 54 Operation 80
- 4.4.4 SSH Settings 81
- 4.4.4.1 SSH Settings 82
- 4.4.5 Authentication 83
- 58 Operation 84
- 4.4.6 Filter Control 87
- 62 Operation 88
- 4.4.7 VLAN 90
- 4.4.8 WDS Settings 92
- 4.4.9 AP Management 92
- 4.4.10 Administration 94
- 4.4.10.3 Upgrading Firmware 95
- 70 Operation 96
- 72 Operation 98
- 4.4.11 System Log 100
- 4.4.11.2 Configuring SNTP 102
- 4.4.12 RSSI 104
- 4.5 SNMP 105
- 80 Operation 106
- 82 Operation 108
- 4.6 Radio Interface 111
- 86 Operation 112
- Radio Interface 113
- 94 Operation 120
- WMM Backoff Wait Times 124
- 100 Operation 126
- 4.6.2 Security 128
- 4.6.2.1 Enabling the VAPs 133
- 108 Operation 134
- 114 Operation 140
- 116 Operation 142
- 4.6.2.4 Configuring 802.1X 144
- 4.7 Status Information 146
- Status Information 147
- 4.7.2 Station Status 148
- 4.7.3 Event Logs 150
- Chapter 5 153
- Command Line Interface 153
- 128 Operation 154
- 5.1.1 Accessing the CLI 155
- 5.1.2 Console Connection 155
- 5.1.3 Telnet Connection 155
- 5.2 Entering Commands 157
- 5.2.5 Partial Keyword Lookup 158
- 5.2.7 Using Command History 159
- 5.2.9 Exec Commands 159
- 5.2.10 Configuration Commands 160
- 5.3 Command Groups 162
- Command Groups 163
- 5.4 General Commands 164
- 5.4.1 configure 165
- 5.4.2 end 165
- 5.4.3 exit 166
- 5.4.4 ping 166
- 5.4.5 reset 167
- 5.4.6 show history 167
- 5.4.7 show line 168
- 5.5.1 country 170
- 5.5.2 prompt 171
- 5.5.3 system name 172
- 5.5.4 username 172
- 5.5.5 password 173
- 5.5.6 ip ssh-server enable 173
- 5.5.7 ip ssh-server port 174
- 5.5.9 ip http port 174
- 5.5.10 ip http server 175
- 5.5.12 ip https port 176
- 5.5.13 ip https server 176
- 5.5.14 APmgmtIP 177
- 5.5.15 APmgmtUI 178
- 5.5.16 show apmanagement 178
- 5.5.17 show system 179
- 5.5.18 show version 180
- 5.5.19 show config 181
- 5.5.20 show hardware 186
- 5.6 System Logging Commands 187
- 5.6.3 logging console 188
- 5.6.4 logging level 188
- 5.6.5 logging facility-type 189
- 5.6.6 logging clear 190
- 5.6.7 show logging 190
- 5.6.8 show event-log 191
- 5.7 System Clock Commands 192
- 5.7.2 sntp-server enable 193
- 5.7.3 sntp-server date-time 193
- 5.7.5 sntp-server timezone 194
- 5.7.6 show sntp 195
- 5.8.1 dhcp-relay enable 196
- 5.8.2 dhcp-relay 196
- 5.8.3 show dhcp-relay 197
- 5.9 SNMP Commands 198
- 5.9.2 snmp-server contact 199
- 5.9.3 snmp-server location 199
- 5.9.5 snmp-server host 200
- 5.9.6 snmp-server trap 201
- 5.9.7 snmp-server engine-id 202
- 5.9.8 snmp-server user 203
- 5.9.9 snmp-server targets 204
- 5.9.10 snmp-server filter 204
- 5.9.12 show snmp groups 206
- 5.9.13 show snmp users 206
- 5.9.15 show snmp target 207
- 5.9.16 show snmp filter 208
- 5.9.18 show snmp 209
- 5.10 Flash/File Commands 211
- 5.10.3 delete 212
- 5.10.4 dir 213
- 5.10.5 show bootfile 214
- 5.11 RADIUS Client 215
- 5.11.2 radius-server port 216
- 5.11.3 radius-server key 216
- 5.11.5 radius-server timeout 217
- RADIUS server 218
- 5.11.10 show radius 219
- 5.12 802.1X Authentication 221
- 5.12.3 802.1x-supplicant user 222
- 5.12.4 show authentication 223
- 5.13.1 address filter default 224
- 5.13.2 address filter entry 225
- 5.13.3 address filter delete 225
- 5.14 Filtering Commands 228
- 5.14.1 filter local-bridge 229
- 5.14.2 filter ap-manage 229
- 5.14.3 filter uplink enable 229
- 5.14.4 filter uplink 230
- (page 205) 231
- 5.14.7 show filters 232
- 5.15 WDS Bridge Commands 233
- 5.16 Spanning Tree Commands 234
- 5.17.1 interface ethernet 235
- 5.17.2 dns server 235
- 5.17.3 ip address 236
- 5.17.4 ip dhcp 237
- 5.17.5 speed-duplex 237
- 5.17.6 shutdown 238
- 5.18.1 interface wireless 241
- 5.18.2 vap 241
- 5.18.3 speed 242
- 5.18.4 multicast-data-rate 242
- 802.11b/g: 1 to 14) 244
- 5.18.7 radio-mode 245
- 5.18.8 preamble 245
- 5.18.9 antenna control 246
- 5.18.10 antenna id 246
- 5.18.11 antenna location 247
- 5.18.12 beacon-interval 247
- 5.18.13 dtim-period 248
- 5.18.14 fragmentation-length 248
- 5.18.15 rts-threshold 249
- 5.18.16 super-g 250
- 5.18.17 description 250
- 5.18.18 ssid 250
- 5.18.19 closed-system 251
- 5.18.20 max-association 251
- 5.18.22 auth-timeout-value 252
- 5.18.23 shutdown 252
- 5.18.25 show station 255
- 5.19.1 rogue-ap enable 257
- 5.19.2 rogue-ap authenticate 258
- 5.19.3 rogue-ap duration 258
- 5.19.4 rogue-ap interval 259
- 5.19.5 rogue-ap scan 259
- 5.19.6 show rogue-ap 260
- 5.20.1 auth 261
- 5.20.2 encryption 263
- 5.20.3 key 263
- 5.20.4 transmit-key 264
- 5.20.5 cipher-suite 265
- 5.20.6 mic_mode 266
- 5.20.7 wpa-pre-shared-key 266
- 5.20.8 pmksa-lifetime 267
- 5.20.9 pre-authentication 267
- 5.21 Link Integrity Commands 269
- 5.21.6 show link-integrity 271
- 5.22 IAPP Commands 272
- 5.23 VLAN Commands 273
- 5.23.2 management-vlanid 274
- 5.23.3 vlan-id 274
- 5.24 WMM Commands 276
- 5.24.3 wmmparam 277
- Appendix A - Troubleshooting 279
- Appendix A -Troubleshooting 280
- Glossary 283
Relacionado con productos y manuales para Redes Alvarion Wi^2 AP CLI
Redes Alvarion BreezeNET B Especificaciones
(232 paginas)
(232 paginas)
Redes Alvarion BreezeNET B300 GigE Manual de usuario
(111 paginas)
(111 paginas)
Redes Alvarion BreezeNET B300 GigE Especificaciones
(56 paginas)
(56 paginas)
Redes Alvarion BreezeNET B300 GigE Manual de usuario
(247 paginas)
(247 paginas)
Redes Alvarion BreezeNET B300 GigE Manual de usuario
(12 paginas)
(12 paginas)
Redes Alvarion BreezeACCESS II CX Guía de usuario
(90 paginas)
(90 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.183 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales